Packing

20 litter air tight Plastic pail

MAGIK 85-20

(UL CLASSIFIED Water Based Quick Tack Duct Adhesive)

MAGIK 85-20 is a UL Classified, zero VOC, a premium quality water-based adhesive, with high tack and rapid setting. MAGIK 85-20 is based on a very special type of synthetic resin, with very high-performance additives, fine grade mineral fillers, and tackifier. MAGIK 85-20 is non-flammable when wet and fire-resistive when dry.

Benefits

  •  Zero Flame spread and Smoke developed
  • Excellent Bonding and Peel Off Strength
  • Solvent Free Synthetic Elastomer Emulsion
  • High Compatibility with Insulation Fiber & Fabric
  • Excellent Coverage
  • Weather Resistant
  • Heat Resistant
  • UV Resistant
  • Moisture Resistant
  • Non Toxic

TECHNICAL SPECIFICATION DATA​

  • Colour                                                           :               Cream
  • Physical form                                              :               Thixotropic Paste
  • Specific Gravity (ASTM D 1475-98)         :               1.20±0.10 kg/ltr
  • Solids Content (ASTM D 1644)                :               65±3 %
  • Viscosity (ASTM D 2196)                          :               10000-20000 cps
  • Flash Point (ASTM D 93)                           :               No Flash to >100C
  • Service Temperature                                  :               Minus 25C to 200C

VOC Content (ASTM D 2369-98)

  • Meets requirements for LEED IEQ 4.1, Low Emitting
  • Materials, Adhesive & Sealants. VOC: 0 g/ltr
Drying Time (ASTM D 1640)

  • Set to Touch: 10 to 15 Minutes
  • Dry Through: 15 to 120 Minutes
 
Coverage Range (subject to surface condition)
 
 5 – 14 m2/ltr (Refer to application procedure section)
 

Storage:

12 months from date of manufacturing in original unopened containers.

Store product (10oC – 40oC) for maximum storage life. Higher temperatures reduce normal storage life. Lower temperatures may cause increased viscosity of a temporary nature. Rotate stock on a “first in-first out” basis.
Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging.

Method of Application

MAGIK 85-20 is recommended for bonding of fire rated duct fabric,
low Density duct liner, duct wrap, & fibrous glass insulation to
painted or unpainted steel, galvanized or aluminum surface.
MAGIK 85-20 can also be applied as a contact bond adhesive,
being applied to both surfaces in areas where water entrapment
may be a problem such as polystyrene to metal. MAGIK 85-20 is
ideal for bonding fibrous glass insulation to concrete, block and
other masonry surface in building construction. MAGIK 85-20 can
also be used for ASJ, FSK, PVDC and PVC Jackets.

Application:

 Brush, spray or roller

Conforms To

  • Military Spec. MIL-A-3316C, Class 2, Grade A.
  • LEED IEQ 4.1, Low Emitting Materials, Adhesive
  • & Sealants (VOC <50 g/ltr).
  • SCAQMD Rule 1168 & 40 CFR 59..
  • NFPA 90A and 90B 25/50.
  • ASTM C916 Type II.
  • DCL Approved.
  • Free of asbestos, lead and mercury compounds.
Surface Preparation:
  •  The surface should be structurally sound, clean, dry, leveled and free from dust, curing compounds, grease and other loose debris. Keep container closed when not in use.
Application Procedure:

For wet bond application apply MAGIK 85-20 uniformly on the metal surface at 8-14 m2/liter. While wet, apply pressure to assure intimate bond.

For contact bond application apply MAGIK 85-20 uniformly on the metal surface at8-12 m2/liter. Coat the insulation surface at 3-5 m2/liter. Allow the adhesive to tack fully and allow the moisture to evaporate for 20-45 minutes, depending on the local environment. Position the two mating surface together and apply pressure to assure intimate bond.